Fluke Process Meter Industrial Calibration Services
Allen Industries calibrates all I/O’s of each port for Fluke meters. Most Metrology services run an automated calibration program that does not check real load voltages, ohms, amps. Accuracy and reliability is paramount when working with electronics and electricity. This is why we have a three part process to ensure reliability and accuracy for all meters, including our own.
Fluke Scopemeter NIST Calibration for ISO9000 Compliance
Allen Industries offers expert NIST calibration services for ISO 9000 compliance. Our calibration service is unparalleled to other Metrology Laboratories as we do not only certify calibrations and provide calibration certificates, as we also repair or clean blemishes, cables, unused outdated cal. stickers, and other problems referred by our customers in our Service Request Form provided by our customers.
Fluke Bench Meter Calibration | Fluke Clamp Meter Calibration Service. Allen Industries calibrates all clamp meters and Fluke is no exception. Most of the calibrators in our facility are Fluke and there is a reason for that. Fluke’ reliability and accuracy are the industry standard and technicians and engineers must have both reliability and accuracy at all times. Clamp meter calibration is performed with a Fluke 5500A and Fluke 5500A/coil.
Fluke Bench Meter Calibration
Allen Industries offers expert NISTcalibration services including repair if needed. Our technician’s receive repairs on a daily basis from Metrology companies because the meter did not pass calibration. Rest assured if a meter does not pass calibration our technicians will offer a repair quote instead of sending it to a third party saving customers time and money.
Allen Industries offers NIST traceable electrical calibration for industrial electrical test equipment. Hand held insulation testers to 1kV to large 80kV insulation testers can be calibrated to NIST standards and repaired as well. One stop shop for high voltage and low ohm meters worldwide with ISO Standards.
Allen Industries offers Factory Calibration for Fluke DSP-4000 cable analyzers and smart remotes. The Fluke DSP-4000 network analyzer must have a software version of 3.7 or higher. If your network analyzer has a lower version then our technicians can offer NIST traceable calibration usually acceptable for government regulations and conformance.
Fluke Networks DSP-4100 Factory Calibration
Fluke Factory calibration for Fluke DSP-4100 cable analyzers must have a software version of 4.7 or higher. Fluke no longer offers factory calibration, however our electronics technician’s have gone to great lengths to offer the same factory calibration as Fluke Corp. To start the factory calibration process please fill out our convenient Quick Quote Form and one of our friendly associates will respond promptly.
Fluke DSP-4300 Factory Calibration
Factory calibration is supported for all versions of software for the Fluke DSP-4300 cable analyzers and smart remotes. After calibration, your Fluke Dsp-4300 cable analyzer screen will show last cal. date as current, (the date our technician’s performed the calibration procedure for the analyzer and smart remote). The same as sending the analyzer to fluke, however Fluke no longer offers calibration. Allen Industries also offers notifications for annual calibrations to help our customers remain in compliance.
Allen Industries not only offers NIST calibration for Fluke Networks, we also offer repair services for all Fluke Networks testers and analyzers. Need NIST calibration for ISO-9000? We perform NIST calibration for all Fluke meters and Fluke Networks products. Allen Industries also offers repair services for all Fluke Networks analyzers and testers.
Allen Industries offers ISO-9000 calibration for the Fluke DTX-1500 cable analyzer and smart remote and also offers annual notifications to our customers for each set of meters needing annual NIST calibration. Allen Industries also rewards our customers for loyalty, the more cable testers sent in for annual calibration the deeper the savings.
Factory Calibration is supported for all versions of software for the Fluke DTX-1800 cable analyzers and smart remotes. After calibration, your Fluke DTX-1800 cable analyzer dates will not change but the calibration certificates will show last cal. date as current, (the date our technician’s performed the calibration procedure for the analyzer and smart remote). The same calibration voltages as sending the analyzer to fluke, however Fluke no longer offers calibration.